Electrostatic Powder Coating Gun Painting Equipment Industrial Sprayer lab spray

Electrostatic Powder Coating Gun Painting Equipment Industrial Sprayer lab spray

JP80 Electrostatic Powder Coating System. The machine is used for the powder coating. Factory to do the spraying experiment and random. Inspection on the powder quality while producing. Can be used for the spraying process test of samples. And test pieces as well as the small scale spraying. Composed of control box, powder coating gun. Cleaning gun and other accessories. The powder feeding system adopts funnel and Venturi. Pipe, and the powder in the powder cup at the back of the gun is drawn into the powder pipe and blown to the gun muzzle under the negative pressure produced when the powder feeding air passing through the Venturi pipe. In the muzzle, the powder will be diluted and speeded up and then spray to the sample. This makes the powder. Feeding be continuous, even, stable, and well-atomized. The static electricity produced system adopts integrated circuit, which works stable; and the boost system adopts. Gun inside multi-voltage boost system, which the consumption of static electricity is low and the spraying rate is high. The control box is portable case, which is used for lab and filed-work. To make the color-change convenient. This machine is configured with a cleaning gun. 50 300g / min(adjust according to need). 1.32LB(600g) (Without pipe and cable). Solenoid valve control voltage. 9.26LB(4.2Kg). The water content should be less than 1.5g / Nm³ (when dew point is 7) and the oil content is less than 0.1mg / Nm³. Width 8.08″ (205mm)×height 3.35″. (85mm)×depth7.88 (200mm). 0.50.6MpaFlow rate15Nm³/h. What you see what you get. And here are showing how to connect. 1 Fix one end of the ground wire on the earth pillar on the back side of the control box and connect another end with the ground wire (wet conductor buried into earth of 0.5m deep outdoor) installed specially and the hanger for hanging work pieces. 2 Insert the plug of the power line into the socket at the back of the control box, and connect the other end with the power supply. The earth pins should be in good earth. 3 Insert the air source pipe (blue) with outer diameter ø8 along with the equipment into the air source connector at the back of control box; and the other end is connected with compressed air resource with oil removing and drying process. The air source pressure: 0.50.6Mpa; the oil content is less than0.1mg/Nm³and the water content is less than 1.5g. 4 Insert the gun connecting cable into the signal output socket at the back of control box, then insert the powder feeding air pipe (outer diameter ø6, black) and atomizing air pipe (outer diameter ø6, blue) into the powder feeding air and atomizing air interface at the back of control box separately. 5 Insert the cleaning gun pipe into the air injection pipe at the back of control box. 6 Check whether the connection of control box, earth wire, spraying gun, cleaning gun, power supply and air source corresponds with the following diagram. Take down the cover of powder cup, fill proper powder (1/53/5 of the capacity of cup) and keep the rim of the cup upwards. Then close the cover. Point the gun to the spraying room (prepare it yourself), and switch on the power supply. Before pulling the trigger, adjust the powder feeding air to the proper pressure (according to the powder output and the manometer indicates about 0.10.3Mpa) and then adjust the atomizing adjusting knob (observe the powder output) to proper position. After that, adjust electrostatic adjusting knob to make it indicate 4070KV (set it to the certain value according to the need). You can spray the work piece (sample) as soon as you finish debugging. If it is needed to clean the dust or the powder on the work piece (sample), cleaning gun can be used to do it. The adjusting nozzle in the front of the cleaning gun can be used to adjust the air flow: rotate right, the flow will be little; conversely, it will be large. What we sell is not only product but also our. Orders are processed from Monday-Friday; Not on the weekends & public holidays. We will work with you to get the case resolved in the fastest method. Hope for your understanding. Please contact with us at first for more details. Defective & Damaged Products. If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. If an item is received damaged, customer service must be contacted within 7 days of receiving your item. Payments via eCheck do not clear immediately. Usually you will wait 5-7 days after checkout for it to clear. The item “Electrostatic Powder Coating Gun Painting Equipment Industrial Sprayer lab spray” is in sale since Wednesday, December 14, 2016. This item is in the category “Business & Industrial\Light Equipment & Tools\Painting Equipment & Supplies\Sprayers”. The seller is “asc365usa” and is located in Scarborough, Ontario. This item can be shipped to United States, Canada.
  • Brand: CN
  • MPN: 013000

Comments are closed.

free blog themes